Description
Note: We do not ship this unit, collection only. Unless you pay separately for the courier guy, the quote is dependent on location.
Backorder: 1st week of Feb 2023
This is a Multi-function pure sine wave inverter & charger that combines an inverter, MPPT solar charge controller, and battery charger capabilities into one portable unit to provide uninterruptible power to your equipment with a small footprint.
The biggest drawcard is that this doesn’t require a DB-based installation or COC certificates, you can simply plug it in and use it as is.
This is a system that is ready to use and plugs into a standard wall outlet. It comes with a great LCD display with multiple functions and a buzzer alert.
The unit is also plug-and-play solar compatible with the built-in 360W Solar charge controller.
Specifications
- Rated Power: 1000W
- Maximum AC 220V Charge Current: 10A
- Rated Solar Charge Current: 30A
- Pure Sinewave for Sensitive Electronics & Motorized Loads
- Comprehensive Display Allows Easy Monitoring & Access of UPS Status
- Solar Array & Battery Common-Anode System Input
- 5V USB Outputs
- SOL-I-BB-M1
This unit is PURE SINE WAVE (the same electrical signal that comes from Eskom), so can run any appliance as long as the total load is less than 1000W
Main Features:
- Excellent performance because of an MCU intelligent control technology
- A wide range of applicable loads because of pure sine wave AC output
- Convenient and practical 5VDC USB output port and 12VDC output port
- Solar array and battery common-anode system input
- Charge by mains supply for flexible configuration (optional function)
- Overcharge protection and over-discharge protection for a longer battery life
- LCD and LEDs for visualization of operation status of the equipment
- Overall automatic protection and alarms Including AC output overload protection, short circuit protection, etc.
Here’s how to maximize your inverter’s battery life ( If you use lead-acid batteries )
- Please leave your inverter kit plugged in and turned on. It will keep your batteries at constant full charge – this is the best state to keep them in.
- If there is no loadshedding, after a few weeks, the acid will start to sulphate on the top of the battery, do the following: Once every 1-2 months, unplug the inverter from the wall and let it run until the inverter starts beeping, then immediately plug it back in. This will circulate the acid and will tremendously increase the life cycle of your batteries.
Do read through this thread on MyBroadband about others who own this unit: Mecer Inverter (Community Support)
| Inverter Specifications | |
| Battery voltage | 12V |
| In-built Battery Specification | 100AH/12V |
| Rated Power | 1000W |
| Output Voltage | 220VAC |
| Output Frequency | 50Hz/60Hz |
| Output Waveform | Pure Sine Wave |
| Mains Input | |
| Rated Voltage | 220VAC |
| Max Charge Current | 10A |
| Solar Input | |
| Maximum Photovoltaic Voltage(VDC) | <25V |
| Charge voltage(VDC) | 10V – 25V |
| Rated Charge Current(A) | 30A |
| Maximum power(Wp) | 360Wp |
| Voltage of overcharge Protection (VDC) | 14.2V |
| Voltage of overcharge Recovery (VDC) | 14.0V |
| Voltage of Floating Charge (VDC) | 13.7V |
| DC Output | |
| Voltage of High-Voltage Protection(VDC) | 16V |
| Voltage of Hit Voltage Recovery (VDC) | 15.2V |
| Voltage of Low Voltage Recovery(VDC) | 12.6V |
| Voltage of Low Voltage Protection(VDC) | 11V |
| 5VDC USB Output Ports | 2 Units |
| Max 2A | |
| 12VDC Output Ports | DC ports(MAX 2A) |
Reviews
There are no reviews yet.